terafoki.blogg.se - Zaccaria pinball greenlight

Zaccaria pinball greenlight how to#
Zaccaria pinball greenlight install#
Zaccaria pinball greenlight drivers#
Zaccaria pinball greenlight driver#

Either is a huge improvement over the one that came with your last IKEA purchase.

A 5/32 hex-key socket (like this) works almost as well but is a tighter fit.

Their handle lacks the forward/reverse switch (have to flip it over). Chapman Manufacturing part CMS-10, or 5120-0, is their 5/32 bit.General's offset screwdriver 8071 is great as it has a forward/reverse switch, but comes with the wrong bits.These are fantastic for working on Stern flippers, and great when working on older Williams cranks. OPTIONAL: Offset screwdriver with 5/32 or 4mm bit.Greatly reduces the number of e-clips that go AWOL. Torpedo level - used for leveling game from side to side.Hemostats (clamps that look a bit like scissors, for soldering).Or it can save a lot of weight in the toolbox. With a set of standard wrenches, this is just a backup. OPTIONAL: One 4" adjustable end wrench.

5/8 wrench - used for leg bolts and all the other leg levelers.9/16 wrench - used for head bolts, some leg bolts, and some leg levelers.UPGRADE: gear wrench.excellent for WPC flipper nuts 3/8 wrench - used for tightening flipper pawls.Some of these are deep enough to envelop certain pots with hexagonal bases. Socket wrench with 9/16 and 5/8 at minimum.Used on newer machines for lock plates and topper domes. Should include #1 and #2 Flat head and Phillips head at minimum. If the almighty repaired pinballs, he'd use one of these. The 8" ones work well for reaching through playfield harnesses.

Zaccaria pinball greenlight drivers#

OPTIONAL: Long nut drivers for 1/4" through 3/8".

They can be useful for getting to playfield locations that are under the head.

OPTIONAL: Stubby nut drivers, particularly 1/4".

Great OPTION: Magnetic tipped nut drivers, especially for driving the hundreds of 1/4" screws into Williams playfields.

Really makes quick work of standard screws.

OPTIONAL: low torque or torque controlled electric screwdriver and 1/4" bit.

Zaccaria pinball greenlight driver#

OPTIONAL: 1/8" nut driver - used for microswitch nuts in some Sega ball troughs.1/4" nut driver - the most common size, used for hex head screws and hex posts.Needle nose pliers - a mini-pliers set is handy.5/16" is used for Stern (DE/Sega) head latches if the game's tool can't be found. You'll probably build your toolset as you go, but the following list is a general set that can accomplish many pinball repairs. 100 Molex header pins (the "break to size" style is the most versatile) Replacement leaf blades and gold flashed contacts.A long lever micro-switch is a generic replacement that you can cut/form to the shape you need. Replacement switch blades and high voltage contacts.Helps with heat in the head as well as they are usually about 50% duty cycle. 455 "Blinker" type bulbs for backglass highlights.Bulbs/Lamps #44/47, #555, and #89 are very common types.Typical sizes for pinball machines are 1.25 inches and 20mm. Fuses are also designed as "fast blow" or "slow blow"/"time delayed blow". Installing a fuse rated higher than spec may cause some other part of the game circuitry to become the weakest link, and damage parts of the game that the fuse is designed to protect.įuses are rated in terms of voltage and most importantly amps.

Zaccaria pinball greenlight install#

If you replace a fuse, and it blows again, then you can be sure that something has gone awry.Īlways install fuses at the rating specified for your game. Locked on coils or flashers, direct shorts of power to ground, and many other reasons will cause a fuse to blow. When too much current is drawn through the circuit, the fuse should be the first part of the circuit to fail.Īlthough fuses sometimes fail due to old age or vibration, fuses usually fail for a reason. They are designed to be the "weakest link" in the circuit. Obviously, this is NOT recommended.įuses are designed into your game's electrical circuitry to protect the circuits from damage should some component fail and begin to draw too much electrical current. This section of PinWiki hosts general information common to all/most pinball machines.

44.10 Cleaning and Adjusting Rollover Switches.

Zaccaria pinball greenlight how to#

43 How to Properly File Switch Contacts.

41 Counterfeit Integrated Circuits & Blacktopped Parts.

27.1 Diode and Switch Matrix Wiring Orientation on a Microswitch.

26 Replacing obsolete/hard to find parts.

23 Testing a Transistor, Silicon Controlled Rectifier (SCR) or Field Effect Transistor (FET).

22.2 Bridge Rectifier Testing Procedure.

22.1 General Information About Bridge Rectifiers.

21 How coils, flashers, and motors are turned on.

13 DIP (Dual In-line Package) Pin Numbering Convention.

11.4 Desoldering Printed Circuit Board Through Hole Components.

11.3.3 Using an old Socket to Align SIPs and Headers.

11.3.2 Repairing traces or creating a "solder stitch".

11.3.1 Bending Discrete Through-hole Components.

11.3 Soldering on Printed Circuit Boards.

6 Repairing Wiring Damaged by IDC Connectors.

4.11 Building a flexible power supply for bench testing PCBs.